Search Results

It is well known that direct injection (DI) is a technology enabler for stratified combustion in spark-ignition (SI) engines. At full load or wide-open throttle (WOT), partial charge stratification can suppress knock, enabling greater spark advance and increased torque. Such split-injection or double-pulse injection strategies are employed when using gasoline in DI (GDI). However, as the use of biofuels is set to increase, is this mode still beneficial? In the current study, the authors attempt to answer this question using two gasoline-alternative biofuels: firstly, ethanol; the widely used gasoline-alternative biofuel and secondly, 2,5-dimethylfuran (DMF); the new biofuel candidate. These results have been benchmarked against gasoline in a single-cylinder, spray-guided DISI research engine at WOT (λ = 1 and 1500 rpm). Firstly, single-pulse start of injection (SOI) timing sweeps were conducted with each fuel to find the highest volumetric efficiency and IMEP.

Conventional diesel-fuelled Partially Premixed Compression Ignition (PPCI) engines have been investigated by many researchers previously. However, the ease of ignition and difficulty of vaporization of diesel fuel make it imperfect for PPCI combustion. In this study, dieseline (blending of diesel and gasoline) was looked into as the Partially Premixed Compression Ignition fuel for its combination of two fuel properties, ignition-delay-increasing characteristics and higher volatility, which make it more suitable for PPCI combustion compared to neat diesel. A series of tests were carried out on a Euro IV light-duty common-rail diesel engine, and different engine modes, from low speed/load to middle speed/load were all tested, under which fuel blend ratios, EGR rates, injection timings and quantities were varied. The emissions, fuel consumption and combustion stability of this dieseline-fuelled PPCI combustion were all investigated.

In-cylinder spray imaging by Mie scattering has been taken with frame rates up to 27,000 fps, along with high speed video photography of chemiluminescence and soot thermal radiation. Spectroscopic measurements have confirmed the presence of OH*, CH* and C2* emissions lines, and their magnitude relative compared to soot radiation. Filtering for CH* has been used with both the high speed video and a Photo-Multiplier Tube (PMT). The PMT signals have been found to correlate with the rate of heat release derived from in-cylinder pressure measurements. A high power photographic strobe has been used to illuminate the fuel spray. Images show that the fuel spray can strike the ground strap of the spark plug, break up, and a fuel cloud then drifts over and under the strap through the spark plug gap. Tests have conducted at two different spark plug orientations using a single spark strategy.

Particulate Matter (PM) legislation for gasoline engines and the introduction of gasoline/ethanol blends, make it important to know the effect of fuel composition on PM emissions. Tests have been conducted with fuels of known composition in both a single-cylinder engine and V8 engine with a three-way catalyst. The V8 engine used an unleaded gasoline (PURA) with known composition and distillation characteristics as a base fuel and with 10% by volume ethanol. The single-cylinder engine used a 65% iso-octane - 35% toluene mixture as its base fuel. The engines had essentially the same combustion system, with a centrally mounted 6-hole spray-guided direct injection system. Particle size distributions were recorded and these have also been converted to mass distributions. Filter samples were taken for thermo-gravimetric analysis (TGA) to give composition information. Both engines were operated at 1500 rpm under part load.

In the catalyst heating operation for a spray guided DISI (Direct Injection Spark Ignition) engine, split injection has been shown to improve combustion stability which is critical for the trade-off between tailpipe emissions and vehicle idle NVH [ 1 ]. The spray guided DISI engine has a multi-hole injector centrally located in the chamber with the spark plug. For catalyst heating operation, the first injection occurs during induction, which forms a relatively well mixed but lean mixture in the cylinder before ignition, and the second injection occurs close to a retarded ignition, which produces a stratified fuel rich mixture in the central region of the combustion chamber. Combustion initialization is found to be sensitive to spark plug protrusion and orientation, injector orientation and 2 nd injection timing relative to ignition [ 1 ].

A single-cylinder Gasoline Direct Injection Engine (GDI) engine with a centrally mounted spray-guided injection system (150 bar fuel pressure) has been operated with stoichiometric and rich mixtures. The base fuel was 65% iso-octane and 35% toluene; hydrogen was aspirated into a plenum in the induction system, and its equivalence ratios were set to 0, 0.02, 0.05 and 0.1. Ignition timing sweeps were conducted for each operating point. Combustion was speeded up by adding hydrogen as expected. In consequence the MBT ignition advance was reduced, as were cycle-by-cycle variations in combustion. Adding hydrogen led to the expected reduction in IMEP as the engine was operated at a fixed manifold absolute pressure (MAP). An engine model has also been set up using WAVE. Particulate Matter (PM) emissions were measured with a Cambustion DMS500 particle sizer.

The paper presents analysis of performance and emission characteristics of a common rail diesel engine operating with RME, with and without EGR. In both cases, the RME fuel was pre-heated in a heat exchanger to control its temperature before being pumped to the common rail. The studied parameters include the in-cylinder pressure history, rate of heat release, mass fraction burned, and exhaust emissions. The results show that when the fuel temperature increases and the engine is operated without EGR, the brake specific fuel consumption (bsfc) decreases, engine efficiency increases and NOx emission slightly decreases. However, when EGR is used while fuel temperature is increased, the bsfc and engine efficiency is independent of fuel temperature while NOx slightly increases.

The differences between modern diesel and gasoline engine configurations are now becoming smaller and smaller, and in fact will be even smaller in the near future. They will all use moderately high compression ratios and complex direct injection strategies. The HCCI combustion mode is likely to lead to the merging of gasoline and diesel engine technologies to handle the challenges they are facing, offering a number of opportunities for the development of the fuels, engine control and after-treatment. The authors' recent experimental research into the HCCI combustion quality of gasoline and diesel blend fuels has referred to the new combustion technology as ‘Dieseline’.

Homogeneous Charge Compression Ignition (HCCI) has emerged as a promising technology for reduction of exhaust emissions and improvement of fuel economy of internal combustion engines. There are generally two proposed methods of realizing the HCCI operation. The first is through the control of gas temperature in the cylinder and the second is through the control of chemical reactivity of the fuel and air mixture. EGR trapping, i.e., recycling a large quantity of hot burned gases by using special valve-train events (e.g. negative valve overlap), seems to be practical for many engine configurations and can be combined with any of the other HCCI enabling technologies. While this method has been widely researched, it is understood that the operating window of the HCCI engine with negative valve overlap is constrained, and the upper and lower load boundaries are greatly affected by the in-cylinder temperature.

This paper presents a computational investigation of the in-cylinder charge characteristics within a motored 4-valve direct injection HCCI engine cylinder with applied negative valve overlapping. Non-typical intake valve strategy was investigated; whereby the pair of intake valves was assumed to follow the same low-lift short-duration valve-lift profile but actuated at different timings. The phase of intake-valve-opening relative to that of exhaust-valve-closing was optimized in terms of pumping losses. The flow fields generated with such an intake valve strategy were compared to those produced in the same engine cylinder but with typical early and late intake-valve-timing. The computational results of such an approach showed modifications in the in-cylinder swirl and tumble motions during the intake and compression strokes.

Planar Laser-Induced Fluorescence has been widely accepted and applied to measurements of fuel concentration distributions in IC engines. The need for such measurements has increased with the introduction of Direct Injection (DI) gasoline engines, where it is critical to understand the influence of mixture inhomogeneity on ignition and subsequent combustion, and in particular the implications for cyclic variability. The apparent simplicity of PLIF has led to misunderstanding of the technique when applied to quantitative measurements of fuel distributions. This paper presents a series of engineering methods for optimizing, calibrating and referencing, which together demonstrate a quantitative measure of fuel concentration with an absolute accuracy of 10%. PLIF is widely used with single component fuels as carriers for the fluorescent tracers.

The burn rate and the instantaneous in-cylinder heat transfer have been studied experimentally in a spray-guided direct-injection spark-ignition engine with three different fuels: gasoline, iso-octane and toluene. The effects of the ignition timing, air fuel ratio, fuel injection timing and injection strategy (direct injection or port injection) on the burn rate and the in-cylinder heat transfer have been experimentally investigated at a standard mapping point (1500 rpm and 0.521 bar MAP) with the three different fuels. The burn rate analysis was deduced from the in-cylinder pressure measurement. A two-dimensional heat conduction model of the thermocouple was used to calculate the heat flux from the measured surface temperature. An engine thermodynamic simulation code was used to predict the gas-to-wall heat transfer.

This paper presents a computational study of the airflow features within a motored 4-valve direct injection engine cylinder. An unconventional intake valve strategy was investigated; whereby each valve on the pair of intake valves was assumed to be actuated with different lifts and duration. One of the intake valves was assumed to follow a high-lift long duration valve-lift profile while the other was assumed to follow a low-lift short duration valve-lift profile. The pair of exhaust valves was assumed to be actuated with two identical low-lift short duration valve-lift profiles in order to generate the so-called negative valve overlapping (NVO). The in-cylinder flow fields developed with such intake valve strategy were compared to those produced in the same engine cylinder but with the application of identical low-lift short duration intake valve events.

Particulate Emissions from Homogeneous Charge Compression Ignition (HCCI) combustion are routinely assumed to be negligible. It is shown here that this is not the case when HCCI combustion is implemented in a direct injection gasoline engine. The conditions needed to sustain HCCI operation were realized using the negative valve overlap method for trapping high levels of residual exhaust gases in the cylinder. Measurements of emitted particle number concentration and electrical mobility diameter were made with a Cambustion DMS500 over the HCCI operating range possible with this hardware. Emissions of oxides of nitrogen, carbon monoxide and unburned hydrocarbons were also measured. These data are presented and compared with similar measurements made under conventional spark ignition (SI) operation in the same engine. Under both SI and HCCI operation, a significant accumulation mode was detected with particle equivalent diameters between 80 and 100 nm.

The blending of oxygenated compounds with gasoline is projected to increase because oxygenate fuels can be produced renewably, and because their high octane rating allows them to be used in substitution of the aromatic fraction in gasoline. Blending oxygenates with gasoline changes the fuels' properties and can have a profound affect on the distillation curve, both of which are known to affect engine-out emissions. In this work, the effect of blending methanol and ethanol with gasoline on unburned hydrocarbon and particulate emissions is experimentally determined in a spray guided direct injection engine. Particulate number concentration and size distribution were measured using a Cambustion DMS500. These data are presented for different air fuel ratios, loads, ignition timings and injection timings. In addition, the ASTM D86 distillation curve was modeled using the binary activity coefficients method for the fuel blends used in the experiments.

A Spray Guided Direct Injection (SGDI) engine has been shown to emit less Particulate Matter (PM) than a first generation (wall guided) Direct Injection Spark Ignition (DISI) engine. The reduction is attributed to the reduced incidence of fuel-wall impingement and higher fuel injection pressure. The extent to which this is true was investigated by comparison between single cylinder SGDI and DISI engines. Both engines were also operated with conventional port injection to provide a baseline. Feedgas PM number concentration and size spectra were measured using a Cambustion differential mobility spectrometer for the fuels iso-octane and toluene with a range of Air-Fuel Ratios (AFRs), ignition and injection timings.

Color-ratio pyrometry (CRP) is a technique for estimating the temperature and loading of soot, based on its thermal emission spectrum. This technique is contrasted with conventional two-color pyrometry which requires absolute measurements of the radiation intensity, either at two specific wavelengths or ranges of wavelengths. CRP uses two ratios, obtained by measuring the radiation intensity for three wavelengths or wavelength bands. CRP has been implemented here by using a digital CCD camera, and full details of the calibration are reported. Because of uncertainties in the emissivity of reference sources (such as tungsten ribbon lamps, in which the emissivity depends on temperature and wavelength), then a spectroscopic calibration of the CCD camera has been used. Use of a CCD camera is not straightforward because of internal digital signal processing (DSP), so full details are given of the calibration and technique implementation.

Exhaust gas temperatures in a 1.4 L, sparked ignition engine have been measured using fine wire thermocouples at different loads and speeds. However the thermocouples are not fast enough to resolve the rapid change in exhaust temperature. This paper discusses a new thermocouple compensation technique to resolve the cycle-by-cycle variations in exhaust temperature by segmentation. Simulation results show that the technique can find the lower time constants during blowdown, reducing the bias from 28 to 4%. Several estimators and model structures have been compared. The best one is the difference equation-least squares technique, which has the combined error between -4.4 to 7.6% at 60 dB signal-to-noise ratio. The compensated temperatures have been compared against combustion parameters on a cycle-by-cycle basis. The results show that the cycle-by-cycle variations of the exhaust temperatures and combustion are correlated.

It is well-known that gasoline is a poor fuel for HCCI operation due to its high autoignation temperature, while the major problem for diesel HCCI is that the ignition temperature of diesel fuel is too low so that diesel autoignites too early. Interestingly a blend of gasoline and diesel fuel could have desirable characteristics for HCCI operation. The negative valve overlap (NVO) is a practical and feasible control mode for production applications of the HCCI concept. At present, the most serious problem is the difficulty to control the moment of auto-ignition and extend the limited operating window of smooth HCCI operation. In this paper, the promotive effects of diesel fuel on gasoline HCCI combustion were experimentally examined. The diesel fuel as additive was added in advance in different proportion (10% and 20% by mass) into gasoline for the purpose of improving its ignitability. The experiments conducted on a gasoline HCCI engine which was naturally aspirated and unthrottled.

There is a worldwide interest in the research of various alternative fuels for automotive engines for the purpose of reduction of CO2 and toxically harmful exhaust emissions. Coal-bed gas, the main component of which is methane, has been considered an attractive alternative fuel for combustion engines due to its abundant resources, high hydrogen-carbon ratios and very low soot formation tendency. The composition of available coal-bed gas, however, can vary considerably, and this has made its combustion stability difficult to control in conventional spark ignition engines. To overcome the problem, a combustion system with a swirl chamber connected to the main combustion chamber through an orifice has been developed for the use of coal-bed gas in spark ignition engines, and the corresponding combustion process has been studied using a developed combustion model involving flame kernel formation and flame front propagation.